Cyclone Hydraulic Reservoir Tank 20 GPM, 2 Gal. removes air from hydraul system

Description: The Cyclone Hydraulic Reservoir represents new thinking in the way that reservoirs are designed and configured for both mobile and industrial applications. This modern design significantly reduces the amount of weight, space, and oil required in a hydraulic system. Hydraulic systems are one of the oldest technologies. It is all around us; from the garbage truck in your neighborhood, the amusement rides at the local festival, to the construction equipment you see working on highways. The lifeblood of a hydraulic system is oil and conventional wisdom has these machines carrying a significant amount of it, until now. Cyclone Hydraulics is changing the way we design, configure and use hydraulic oil reservoirs. A Major Function Of A Hydraulic Reservoir Is To Remove Air Conventional reservoirs do not remove a majority of air from the hydraulic system. Traditional hydraulic systems do not allow sufficient time to remove entrained air which is a major cause of hydraulic component failure. Utilization of the Cyclone reservoir RAPIDLY removes a majority of air from the oil.Hydraulic Reservoir Sizing A traditional hydraulic reservoir should contain 1 to 5 times the amount of oil that the pump can produce in one minute. A 20 gallon per minute (GPM) system may need 20-100 gallons of oil and weigh 250-1200 pounds (including oil) and require a significant space claim. A Cyclone Hydraulic Reservoir can reduce the amount of oil necessary in a hydraulic system by 10-20 times! A 20 GPM system will may only need 2 gallons of oil and weigh as little as 30 pounds (including oil) with minimum space claim. The Cyclone Reservoir is designed to rapidly remove entrained air fromhydraulic fluid. As the name implies, it efficiently accomplishes this task byway of well-known cyclonic action. As fluid is returned to the reservoir it is forced to revolve at a very highrate of speed. The heavier, non-aerated fluid is forced to the outside wall of the reservoir interior whereby it isavailable at the pump inlet port. The lighter air bubbles migrate to the center of the reservoir and aredissipated through the filler/breather cap.Being far more efficient at removing entrained air than a conventional hydraulic reservoir, the Cyclonedramatically reduces the volume of fluid required to be stored within the reservoir. Reductions in reservoir sizeand installed weight of up to 90 percent are possible as compared to traditional reservoir Construction - high strength nylonDiameter - 8.9 In. (226 mm)Height - 15.5 In. (394 mm)Space Claim - 0.75 Cu. Ft. (21 liter)Maximum Flow Rate - 20 GPM (75.7 lpm)Minimum Flow Rate - 10 GPM (37.9 lpm) toinsure adequate cyclonic actionSuction Head @ Max Flow - 0.25 PSI (1.72 kPa)Makeup Volume - 0.62 GAL (2.38 liter)Total Volume- 2.00 GAL (7.57 liter)Dry Weight - 9.64 Lbs. (4.37 kg)Maximum Ambient Temperature - 220º F(104º C)Maximum Pressure Capability - 5 PSIG (0.35Bar) Gradability - 60% Grade (31º angle)Filtration - the Cyclone Reservoir makes noclaim to filter contaminants from the fluid. Thistask must be performed by way ofexternal pressure or return line filtration.Heat Exchangers - the Cyclone Reservoirmakes no claim to remove heat from the fluid.This task must be performed by way ofexternal return line heat exchange equipment.Fluid Compatibility - the Cyclone Reservoir iscompatible with most traditional hydraulic fluids.Level Switch - 12 or 24 Vdc, normally openwhen level is low. Max current equals 1.0 Amp.Connector is Deutsch DT04-2P.Installation - it is recommended that eachconnection hose be clamped to the machinewithin 12” or the reservoir.

Price: 250 USD

Location: Denver, Colorado

End Time: 2023-10-10T16:22:17.000Z

Shipping Cost: N/A USD